Tutorials How to configure floating IP on CentOS

How to configure floating IP on CentOS

When you attach a new floating IP, you can find it listed to one of the servers at your UpCloud control panel that the floating IP currently points to. However, using the new floating IP will require some manual setup. Follow the steps below on how to get this done on Ubuntu servers.

As an example, we have a cloud server with the public IP address 185.20.139.167, a floating IP 185.20.139.29, with a netmask 255.255.255.255. These are highlighted below in red.

Before making changes to your network configuration, it’s always a good idea to take a backup. Also, note that if your network configuration becomes inoperable, remember that you can always log in to your cloud server using the console connection.

Configuring floating IP

Firstly, you’ll need to configure the servers at the OS level, so start up your cloud server at your UpCloud control panel and log in.

Check your current network settings with the following command.

ip addr

Commonly the second network interface card (NIC) named eth0, highlighted in red, has your public IPv4 address assigned to it.

2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
   link/ether 6e:d7:1b:bf:3a:5f brd ff:ff:ff:ff:ff:ff
   inet 185.20.139.167/22 brd 185.20.139.255 scope global eth0
      valid_lft 53810sec preferred_lft 53810sec

On CentOS hosts, each NIC is controlled by its own configuration file. You will need to create a new network interface configuration file for the floating IP. The easiest way to do this is to duplicate the configuration file of the NIC with your regular IP, this way you don’t need to write the whole file from scratch.

For example, with eth0 you can use the following command.

sudo cp /etc/sysconfig/network-scripts/ifcfg-eth0 /etc/sysconfig/network-scripts/ifcfg-eth0:1

Then edit the new alias interface.

sudo vi /etc/sysconfig/network-scripts/ifcfg-eth0:1

Add the same “:1” to the device name, enter a new parameter NM_CONTROLLED=no, replace the IP address with the floating IP and then remove the gateway line.

DEVICE=eth0:1
BOOTPROTO=static
ONBOOT=yes
NM_CONTROLLED=no
IPADDR=185.20.139.29
NETMASK=255.255.255.255

Save the file and exit after these changes.

Finally, restart your network manager to enable the changes.

sudo systemctl restart network

If you were connected with SSH, the networking restart should not cause you to disconnect. In case you do lose connection and are unable to reconnect, you can always use the web Console at UpCloud control panel under your Server settings to go through the setup again to make sure everything is entered correctly.

Repeat the process to add the alias on any other servers you wish to use the floating IP on.

Testing the configuration

Your configuration is now complete. You can test that it works by transferring the floating IP from one server to another.

First, ping the cloud server or attempt to connect to your server through the floating IP via SSH. Alternatively, if you have a web server configured, open the floating IP on your web browser.

Then transfer the floating IP to another cloud server you’ve configured. This can be done either at your UpCloud control panel or by using the UpCloud API.

Test the floating IP again with any method you prefer. When you get a connection you have successfully transferred your floating IP.

When you get a reply, the floating IP works on that server and you can continue forward. If it didn’t work, make sure you entered the IP address and netmask correctly, that your firewall isn’t blocking your connections, or try another method to connect.

Using your new floating IP

You can now transfer the floating IP between your cloud servers at your UpCloud control panel or by using the UpCloud API!

Depending on your intended use case for the floating IP you may wish to continue by setting up automated load balancing, but it’s always possible to manually transfer the traffic between your servers.

2 thoughts on “How to configure floating IP on CentOS

    1. Hi Bill, thanks for checking out the guide. Managing a floating IP will require some care to be used appropriately. This guide only covers the examples for enabling and testing the floating IP.

Leave a Reply

Your email address will not be published. Required fields are marked *

Locations

Helsinki (HQ)

In the capital city of Finland, you will find our headquarters, and our first data centre. This is where we handle most of our development and innovation.

London

London was our second office to open, and a important step in introducing UpCloud to the world. Here our amazing staff can help you with both sales and support, in addition to host tons of interesting meetups.

Singapore

Singapore was our 3rd office to be opened, and enjoys one of most engaged and fastest growing user bases we have ever seen.

Seattle

Seattle is our 4th and latest office to be opened, and our way to reach out across the pond to our many users in the Americas.